Budget cost form

	N°	Component/Activity	Description	Cost	Number of pieces
		Acid Ferric	This kind of acid is used to eliminate the excess of cooper in the Bakelite	$                39.00	X2
		Acrylic	This material is similar to crystal but is more resistance and lighter	$                99.00	X1 meter
		Arduino	This is a microcontroller platform, it’s like the brain of the project. We will use that to control all the dispositives.	$             300.00	X1
		Bakelite	This material is used to make the circuits of the project.	$                40.00	X1 30cm
		Water Bombs	The water bombs are used to collect the water and fill in the glass	$                  70	X5
		Cable	The cable is going to be to connect all the circuits with the bombs, servomotor and sensors.	$                  9.00	X1 5meter
		Display	The display is a little screen that shows numbers. We will going to show the number of full glasses.	$                55.00	X1
		Hose	This hose will going to be with the water booms to fill the glasses	$                15.00	X1 6meter
		RGB Sensor (tcs 3200)	The RGB sensor detects the different color of the glasses	$              175.00	X1
		Servomotor	The servomotor is a motor that you can control. This will move the base with the glasses	$              162.00	X1
		Screws	They will be in all of the structure of the project	$                  1.00	X40
		Relays	This dispositive is a switch to turn on and turn off the waterboms and the servomotor	$                  30.00	X5
			Total:	994$	1554

IP report

The integrator project going in a timely manner, there have been several advances, but I left my team that work hard, because I had a lot of work at my job, I think they're a bit stressed.

The progress has been made in the structure and the programming, calibrate the RGB sensor, but progress is needed in the design.,and the sensor was tested with servo motor and works great, just slightly adjust the rotation.

The water pumps consume much amperage will be in service but only few seconds, with good voltage source pumps work well and fill the glasses quickly.

Refine several details still missing but I will finalize the project.I hope I'm not stressed by the end of the semester with the delivery of the project and finish it in time allotted.

how to change a flat tire

blog activity #1

Instructions to change a tire.

1. Check the spare tire
2. Loosen the wheels nuts
3. Put the jack under the car
4. Raise the car with the jack, be careful
5. Take off the old wheel
6. Put on the spare tire
7. Tighten the wheel nuts
8. Lower the car and take the jack away
9. Tighten the wheel nuts again until lock the wheel.
10. The flat tire away, and put in the trunk. 

Diagram 

Integrated Project “Write Up”
Team number		5
Group Members		ALTAMIRA JASSO MAURICIO ALFREDO BECERRIL HOYOS DANIEL CAÑEDO CAMPOS CARLOS HUMBERTO(ME) LARA SALAS YERADI GUADALUPE VAZQUEZ CHAVEZ YOLANDA VERONICA
My responsibilities
I have the responsability of desing the document, design some pieces in solidworks software, buy the components to make the prototype, also coordinate my partners to work always together.
Scope
our project will be a classify machine of drinks, it works by RGB sensor, the flavor drink´s depend of the color of the plastic cup. this project will be benefit for the restaurats bussines, make a control of drinks and little quickly the service.
Communication strategies
our team are comunicate using the internet tools, like facebook, gmail, hotmail, google drive. and text messages by smartphones.

sunday works

beautiful afternoon in my work, but i´ll wish to be resting in my home haha.

i work for you have electric energy :)

My reason for use a blog.

Advantages

-Interactive with classrom friends
-Post comments in friends blogs for practice our english
-search many blogs for support my english
-search information for my homeworks

Disadvantages

-distractions if no use correctly
-post offensive commets in a friends blogs

Links for support my english and homeworks

http://menuaingles.blogspot.mx/
http://cmecafenix.blogspot.mx/

hello world!
my name is Carlos Canedo
my hobbies are swing, play guitar.
I like coffe, movies, sushi, pizza.
I work in a thermoelectric central and also i study the carrer of Mechatronics Engeenier.

my strategies to learn english are watch movies, series.

my future plans is complete the mechatronics engeenier carrer, and create my owm company of automatization and electrical maintenance.

and... this is a little information of myself.

thank you for visit my blog.